JMC ROKKER 1000XXR A2B 2/4-CH AMPLIFIER / 2-SPEAKER KIT 2023 ½ - 2025 HARLEY ROADGLIDE / STREETGLIDE / CVO

Peak Power Output: 2040w Peak Power – 510w x 4CH – 2-ohm load at 14.4vdc
RMS Output Power: 920w RMS - 230w x 4CH - 2-ohm
Amplifier Class: New high-efficiency Class-D IC circuitry, (no cooling fans needed) properly shielded against FM/AM radio interference
Marine Grade Protection: PCB is conformal coated for complete protection against water damage in the motorcycle or powersports environment
Power Supply: 12v Digital Switching – Very Low Amperage Draw Compared to Other Brands in this Power Range
A2B Integrated Converter: Special Integrated A2B ROKKER 1000XXR Amplifier replaces the stock Harley amplifier completely during the installation (NO Amplifier Piggy-Backs)
Radio Compatibility: Compatible with the stock Harley Radio, NO special radio flashes or adjustments are needed
Rear Speaker Ready: This amp kit automatically connects into the rear speaker output wires already built into the stock Harley wire harness, to allow direct plug in under the seat for rear mounted saddlebag-lid or trunk-pod speakers, using the applicable rear speaker wiring harness
Mounting Options: Mounts into the in-fairing cradle with JMC brackets and mounting hardware
External Dimensions: 7 ¼” x 4 ¾” x 1 ¾” (in.)
ROKKER Speaker Size: 6.71” (in.) Diameter
Cone Construction: Black Glass-Fiber
Integrated Tweeter: PEI Dome High-Output
Frequency Response: 30-23kHz
Sensitivity: 90 db
Magnet Material: Lightweight Neodymium
Impedance: 2 Ohms
Maximum Power: 300 Watts
RMS Power: 230 Watts
Mounting Depth: 2 7/8” (in.)
Weather Resistant: Yes
OEM Size Match: Yes
Comparision Rating: ROKKER speaker and amplifier kits provide lower distortion levels, better bass response and superior highway performance, compared to stock Harley, Fosgate or Hertz

Description

This new JMC ROKKER® 1000XXR stage6 fairing/rear speaker amplifier kit has been designed specifically for use on the 2023 ½ - 2025 Harley RoadGlide, StreetGlide or CVO.

A2B converter is integrated into the ROKKER 1000XXR amp and is 100% plug-n-play into the electrical system, providing 2/4-channels of amplification at 230w RMS power per-channel x4 (920w RMS total) into a 2-ohm speaker load. (No more stock Amp Piggy-Backs)

New high-efficiency Class-D IC circuitry, (no cooling fans needed) properly shielded against FM/AM radio interference.

PCB is conformal coated for complete protection against water damage in the motorcycle or powersports riding environment.

This ROKKER amplifier uses advanced digital switching power supply technology to dramatically reduce the 12v current demands on the motorcycle electrical system, compared to other brand amplifiers in this power range.

ROKKER amplifier mounts into the in-fairing cradle with included JMC brackets and mounting hardware.

This amp kit automatically connects into the rear speaker output wires already built into the stock Harley wire harness, to allow direct plug in under the seat for rear mounted saddlebag-lid or trunk-pod speakers, using the applicable rear speaker wiring harness.

This new ROKKER series amplifier comes out of the box already dialed in for this specific speaker configuration, using the Harley radio’s built-in DSP controls to provide lower distortion levels, better bass response and superior highway performance, compared to stock Harley, Fosgate or Hertz.

Also included are our custom made heavy-gauge power and ground wires used for the fused battery & frame connections, along with all necessary mounting hardware & complete installation/operation instructions.

Amplifier itself measures 7 ¼” x 4 ¾“ x 1 ¾” (in.)

JMC's ROKKER XXR series 6.71" speakers are designed as exact size component/replacements for the stock 6.5" Harley fairing speakers as installed on the 2023 1/2 - 2025 Harley StreetGlide, RoadGlide or CVO.

Spec'd at 2 ohms impedance and 300 watts maximum input (230w RMS - 90db sensitivity).

Lightweight waterproof one-piece woven-fiber driver cone with super-rigid metal basket design.

High-density lite-weight Neodymium magnet structure, specially coated to maintain flux-strength integrity even at extreme operating temperatures.

Integral high-output PEI dome tweeter.

Mounting hole pattern and spade electrical connections are exactly the same as the factory specification, this is a total plug-and-play no-modification solution complete with easy to follow installation instructions.

These are THE MOST powerful speakers you can buy for your Harley and they will perform extremely well when connected to a medium or large sized accessory amplifier.